ANALISIS PENGENDALIAN KUALITAS PRODUK CYLINDER HEAD COVER DENGAN METODE SPC (Statistical Proccesing Control) DAN FMEA (Failure Mode And Effect Analysis) PADA PT. TOYOTA BOSHOKU INDONESIA

RAMADHAN, ALFIAN (2020) ANALISIS PENGENDALIAN KUALITAS PRODUK CYLINDER HEAD COVER DENGAN METODE SPC (Statistical Proccesing Control) DAN FMEA (Failure Mode And Effect Analysis) PADA PT. TOYOTA BOSHOKU INDONESIA. S1 thesis, Universitas Mercu Buana Bekasi.

[img]
Preview
Text
1. HALAMAN JUDUL.pdf

Download (35kB) | Preview
[img]
Preview
Text
2. ABSTRAK.pdf

Download (103kB) | Preview
[img]
Preview
Text
3. SURAT PERNYATAAN.pdf

Download (294kB) | Preview
[img]
Preview
Text
4. LEMBAR PERNGESAHAN.pdf

Download (321kB) | Preview
[img]
Preview
Text
5. KATA PENGANTAR.pdf

Download (150kB) | Preview
[img]
Preview
Text
6. DAFTAR ISI.pdf

Download (111kB) | Preview
[img]
Preview
Text
7. DAFTAR GAMBAR.pdf

Download (144kB) | Preview
[img]
Preview
Text
8. DAFTAR TABEL.pdf

Download (124kB) | Preview
[img] Text
9 . BAB 1.pdf
Restricted to Registered users only

Download (175kB)
[img] Text
10. BAB 2.pdf
Restricted to Registered users only

Download (358kB)
[img] Text
11. BAB 3.pdf
Restricted to Registered users only

Download (293kB)
[img] Text
12. BAB 4.pdf
Restricted to Registered users only

Download (1MB)
[img] Text
13. BAB 5.pdf
Restricted to Registered users only

Download (131kB)
[img] Text
14. BAB 6.pdf
Restricted to Registered users only

Download (107kB)
[img] Text
15. DAFTAR PUSTAKA.pdf
Restricted to Registered users only

Download (156kB)
[img] Text
16. LAMPIRAN.pdf
Restricted to Registered users only

Download (268kB)

Abstract

ABSTRAK PT. Toyota Boshoku Indonesia adalah sebuah perusahaan manufaktur yang memproduksi komponen dan interior otomotif, salah satu produk yang dihasilkan adalah Cylinder Head Cover (CHC). Dari penelitian yang dilakukan terlihat pengendalian kualitas pada produksi CHC masih belum mampu memenuhi target yang ditetapkan perusahaan .Untuk mengatasi masalah pengendalian kualitas, maka pada penelitian ini menggunakan metode Statistical Processing Control (SPC) dan Failure Mode and Effect Analysis (FMEA). SPC merupakan sebuah teknik statistik yang digunakan secara luas untuk memastikan bahwa proses memenuhi standar. FMEA merupakan salah satu metode yang digunakan untuk pengendalian kualitas dalam proses fabrikasi. Berdasarkan hasil analisis yang dilakukan pengendalian kualitas pada produksi CHC belum dapat terkendali hal ini diakibatkan oleh tingginya tingkat kecacatan produk yang disebabkan oleh kecacatan Blowpipe Burry dengan presentase kecacatan sebesar 42.93% dan Stamp Part Number Blur dengan presentase sebesar 21,03%, penyebab potensi kegagalan yang terjadi disebabkan karena Pengecekan area Blowpipe hanya berdasarkan visual serta Stopper Box menggores area part number dengan nilai RPN masing-masing sebesar 280 dan 90, usulan perbaikan berupa membuat alat bantu pegecekan area Blowpipe dan menambahkan item pengecekan area Blowpipe pada lembar instruksi kerja serta memodifikasi Stopper Box dan memastikan tidak menyentuh area Part Number. Kata Kunci : Statistical Processing Control (SPC), Failure Mode and Effect Analysis (FMEA), Pengendalian Kualitas ABSTRACT PT. Toyota Boshoku Indonesia is a manufacturing company that manufactures automotive parts and interiors, one of the products produced is the Cylinder Head Cover (CHC). From the research carried out it appears that quality control in CHC production has not been able to meet the desired target of the company. To overcome the problem of quality control, this research uses Statistical Processing Control (SPC) and Failure Mode and Effect Analysis (FMEA) methods. SPC is a statistical technique that is widely used to ensure that processes meet standards. FMEA is one of the methods used for quality control in the fabrication process. Based on the results of the analysis conducted quality control on CHC production cannot be controlled yet this is due to the high level of product defect caused by Blowpipe Burry disability with a percentage of disability of 42.93% and Stamp Part Number Blur with a percentage of 21.03%, the cause of potential failures This is caused by checking the Blowpipe area only based on visuals and Stopper Box scratching the part number area with an RPN value of 280 and 90 respectively, the proposed improvement in the form of making a Blowpipe area checking tool and adding Blowpipe area checking items on the work instruction sheet and modifying the Stopper Box and make sure it doesn't touch the Part Number area. Keywords: Statistical Processing Control (SPC), Failure Mode and Effect Analysis (FMEA), Quality Control

Item Type: Thesis (S1)
Call Number CD: FT/IND 20 001
NIM/NIDN Creators: 41615210018
Uncontrolled Keywords: Kata Kunci : Statistical Processing Control (SPC), Failure Mode and Effect Analysis (FMEA), Pengendalian Kualitas
Subjects: 600 Technology/Teknologi > 620 Engineering and Applied Operations/Ilmu Teknik dan operasi Terapan > 628 Sanitary Engineering and Environmental Protection Engineering/Rekayasa Sanitasi dan Teknik Perlindungan Lingkungan, Teknik Lingkungan > 628.5 Pollution Control and Industrial Sanitation Engineering/Pengawasan Polusi dan Teknik Sanitasi Industri
700 Arts/Seni, Seni Rupa, Kesenian > 750 Painting and Paintings/Seni Lukis dan Lukisan > 758 Other Subjects/Subjel Lainnya > 758.6 Industrial and Technical Subjects/Subjek Industri dan Teknik
Divisions: Fakultas Teknik > Teknik Industri
Depositing User: siti maisyaroh
Date Deposited: 02 Mar 2022 04:16
Last Modified: 02 Mar 2022 04:16
URI: http://repository.mercubuana.ac.id/id/eprint/57032

Actions (login required)

View Item View Item