ANALISIS KEKUATAN STRUKTUR PROTOTIPE TELESKOPIK KONVEYOR OTOMATIS DENGAN PERANGKAT LUNAK SOLIDWORK

SALSABIL, MUHAMMAD IQBAL (2022) ANALISIS KEKUATAN STRUKTUR PROTOTIPE TELESKOPIK KONVEYOR OTOMATIS DENGAN PERANGKAT LUNAK SOLIDWORK. S1 thesis, Universitas Mercu Buana Bekasi.

[img]
Preview
 Text
41316310081-MUHAMMAD IQBAL SALSABIL-01 COVER.pdf
Download (161kB) | Preview
[img]
Preview
 Text
41316310081-MUHAMMAD IQBAL SALSABIL-02 ABSTRAK.pdf
Download (51kB) | Preview
[img] Text
41316310081-MUHAMMAD IQBAL SALSABIL-03 BAB I.pdf
Restricted to Registered users only
Download (44kB)
[img] Text
41316310081-MUHAMMAD IQBAL SALSABIL-04 BAB II.pdf
Restricted to Registered users only
Download (216kB)
[img] Text
41316310081-MUHAMMAD IQBAL SALSABIL-05 BAB III.pdf
Restricted to Registered users only
Download (147kB)
[img] Text
41316310081-MUHAMMAD IQBAL SALSABIL-06 BAB IV.pdf
Restricted to Registered users only
Download (252kB)
[img] Text
41316310081-MUHAMMAD IQBAL SALSABIL-07 BAB V.pdf
Restricted to Registered users only
Download (45kB)
[img] Text
41316310081-M.IQBAL SALSABIL- 09 DAFTAR PUSTAKA.pdf
Restricted to Registered users only
Download (20kB)

Abstract

ABSTRAK Di tengah perkembangan ilmu pengetahuan yang semakin tinggi, salah satunya peralatan teleskopik konveyor otomatis, sistem teleskopik konveyor otomatis umumnya digunakan untuk memindahkan material dari satu tempat ke tempat lain. Biasanya sistem teleskopik konveyor otomatis memiliki rangka memanjang yang dipasang untuk timbal balik gerakan pada rangka dasar memanjang, dalam pemilihan material untuk pembuatan rangka, antara lain kekuatan, kekerasan dan kekuatan lelah, yang harus diperhatikan adalah sifat-sifat pada bahan, sifat pada bahan didefinisikan sebagai tolak ukur kemampuan material untuk menahan gaya atau tegangan dan faktor keamanan seharusnya lebih besar daripada 1,0 untuk menghindari kegagalan. Maka faktor keamanan yang nilainya sedikit di atas 1,0 hingga 10 yang akan digunakan, berdasarkan landasan teori tersebut, didapatkan rumusan masalah dari struktur yaitu belum diketahuinya nilai maksimum dari tegangan, deformasi serta nilai faktor keamanan dari konveyor teleskopik otomatis tersebeut, agar konveyor teleskopik otomatis ini bisa implementasikan di dunia industri maka kita harus mengetahui nilai dari parameter parameter tersebut, Untuk mengetahuinya pada penelitian ini digunakan metode analisis simulasi static menggunakan Perangkat Lunak solidworks dengan jumlah pembebanan 225,55 N didapatkan hasil dari tegangan maksimum tersebut 2.397 Ν/ yang mana nilai yield strength matrial tersebut adalah 2.500 Ν/ serta diketahui juga nilai deformasi maksimum sebesar 1,9 mm dan diketahui juga nilai keamanannya berada diangka 2,4 yang artinya teleskopik konveyor otomatis ini dikatakan aman. Kata Kunci : konveyor teleskopik otomatis,struktur, solidworks, tegangan, deformasi, faktor keamanan. ABSTRACT In the midst of increasingly advanced scientific developments, one of which is automatic conveyor telescopic equipment, automatic conveyor telescopic systems are generally used to move materials from one place to another. Usually the automatic conveyor telescopic system has a longitudinal frame mounted for reciprocal movement on the longitudinal base frame, in the selection of materials for the manufacture of the frame, including strength, hardness and fatigue strength, which must be considered are the properties of the material, the properties of the material are defined as a measure of the material's ability to withstand forces or stresses and the safety factor should be greater than 1.0 to avoid failure. Then the safety factor whose value is slightly above 1.0 to 10 that will be used, based on the theoretical basis, the formulation of the problem from the structure is not yet known, the maximum value of stress, deformation and the value of the safety factor of the automatic telescopic conveyor, so that the automatic telescopic conveyor is not known. If this can be implemented in the industrial world, we must know the value of these parameters. To find out, in this study, a static simulation analysis method was used using Solidworks Software with a total loading of 225.55 N, the result was that the maximum stress was 2,397 / which where the yield strength value of the material is 2,500 / and it is also known that the maximum deformation value is 1.9 mm and it is also known that the safety value is at 2.4, which means that this automatic telescopic conveyor is said to be safe. Keywords : automatic telescopic conveyor, structure, solidworks, stress, deformation, safety factor.

Item Type: Thesis (S1)
Call Number CD: FT/MSN 22 006
NIM/NIDN Creators: 41316310081
Uncontrolled Keywords: Kata Kunci : konveyor teleskopik otomatis,struktur, solidworks, tegangan, deformasi, faktor keamanan.
Subjects: 600 Technology/Teknologi > 620 Engineering and Applied Operations/Ilmu Teknik dan operasi Terapan > 621 Applied Physics/Fisika terapan > 621.8 Machine Engineering, Machinery/Teknik Mesin
Divisions: Fakultas Teknik > Teknik Mesin
Depositing User: siti maisyaroh
Date Deposited: 21 Dec 2022 06:22
Last Modified: 21 Dec 2022 06:22
URI: http://repository.mercubuana.ac.id/id/eprint/72670

Actions (login required)

View Item View Item
UMB Repository is powered by EPrints 3 which is developed by the School of Electronics and Computer Science at the University of Southampton. More information and software credits.