ROMADHON, ARIEF (2020) ANALISIS PENGARUH PARAMETER PROSES CETAK PLASTIK SISTEM INJEKSI TERHADAP CACAT SHRINKAGE PADA OIL FILLER CAP DENGAN METODE TAGUCHI DAN ANALYSIS OF VARIENCE (ANOVA). S1 thesis, Universitas Mercu Buana Jakarta.
|
Text (HAL COVER)
1. Halaman Judul.pdf Download (208kB) | Preview |
|
|
Text (ABSTRAK)
2. Abstrak.pdf Download (159kB) | Preview |
|
|
Text (LEMBAR PERNYATAAN)
3. Lembar Pernyataan.pdf Download (923kB) | Preview |
|
|
Text (LEMBAR PENGESAHAN)
4. Halaman Pengesahan.pdf Download (70kB) | Preview |
|
|
Text (KATA PENGANTAR)
5. Kata Pengantar.pdf Download (141kB) | Preview |
|
|
Text (DAFTAR ISI)
6. Daftar Isi.pdf Download (331kB) | Preview |
|
|
Text (DAFTAR TABEL)
7. Daftar Tabel.pdf Download (139kB) | Preview |
|
|
Text (DAFTAR GAMBAR)
8. Daftar Gambar.pdf Download (259kB) | Preview |
|
|
Text (DAFTAR LAMPIRAN)
9. Daftar Lampiran.pdf Download (89kB) | Preview |
|
Text (BAB I)
10. Bab 1.pdf Restricted to Registered users only Download (995kB) |
||
Text (BAB II)
11. Bab 2.pdf Restricted to Registered users only Download (4MB) |
||
Text (BAB III)
12. Bab 3.pdf Restricted to Registered users only Download (853kB) |
||
Text (BAB IV)
13. Bab 4.pdf Restricted to Registered users only Download (1MB) |
||
Text (BAB V)
14. Bab 5.pdf Restricted to Registered users only Download (331kB) |
||
Text (DAFTAR PUSTAKA)
15. Daftar Pustaka.pdf Restricted to Registered users only Download (529kB) |
||
Text (LAMPIRAN)
16. Lampiran.pdf Restricted to Registered users only Download (257kB) |
Abstract
Almost every product used in everyday is made of plastic and most of these products can be produced by injection molding methods. A good mold will produce a product that matches the expected shape and dimensions. The existence of shrinkage causes discrepancies between the dimensions of the mold with the product. Inaccurate products can affect the function of a product. Oil filler cap is an automotive component that have function as a cover for oil filling holes in the automatic engine 110 cc, inaccurate oil filler cap can cause oil to seep out. To resolve this problem, it is necessary to make a precise oil filler cap. By simulating the process using the Autodesk Moldflow Insight software, optimal process parameters can be identified so that the minimum shrinkage is obtained. From the simulation results, it was found that the optimal parameter combination for the plastic molding process of oil filler cap products included injection temperature of 200 ° C, mold temperature of 80 ° C, holding pressure of 105 MPa, and holding pressure time of 9 seconds. With these parameter settings, the shrinkage value for thread diameter is 0,55% (0.11 mm) from diameter mold is 20 mm. Keywords: injection molding, shrinkage, taguchi method, Autodesk Moldflow Insight, oil filler cap Hampir setiap produk yang digunakan dalam kehidupan sehari-hari melibatkan penggunaan plastik dan sebagian besar diantaranya dapat diproduksi dengan metode injection molding. Cetakan yang baik akan menghasilkan produk yang sesuai dengan bentuk dan dimensi yang diharapkan. Adanya shrinkage menyebabkan ketidaksuaian antara dimensi cetakan dengan produk. Produk yang tidak presisi dapat mempengaruhi fungsi dari suatu produk. Oil filler cap merupakan salah satu komponen otomotif yang berfungsi sebagai penutup lubang pengisian oli pada mesin motor matic 110 cc, oil filler cap yang tidak presisi dapat menyebabkan oli bisa merembes keluar. Untuk mengatasi masalah tersebut, maka perlu dibuat oil filler cap yang presisi. Dengan simulasi proses menggunakan software Autodesk Moldflow Insight dapat diketahui parameter proses yang optimal sehingga didapatkan shrinkage yang minimum. Dari hasil simulasi didapatkan kombinasi parameter optimal untuk proses cetak plastik produk oil filler cap diantaranya temperatur injeksi 200 °C, temperatur cetakan 80 °C, holding pressure 105 MPa, dan holding pressure time 9 detik. Dengan setting parameter tersebut didapatkan nilai shrinkage pada bagian diameter ulir sebesar 0,55% (0,11 mm) dari diameter cetakan 20 mm. Kata kunci: cetak plastik sistem injeksi, shrinkage, metode taguchi, Autodesk Moldflow Insight, oil filler cap
Actions (login required)
View Item |