ANALISIS PENGARUH PARAMETER PROSES CETAK PLASTIK SISTEM INJEKSI TERHADAP CACAT SHRINKAGE PADA OIL FILLER CAP DENGAN METODE TAGUCHI DAN ANALYSIS OF VARIENCE (ANOVA)

ROMADHON, ARIEF (2020) ANALISIS PENGARUH PARAMETER PROSES CETAK PLASTIK SISTEM INJEKSI TERHADAP CACAT SHRINKAGE PADA OIL FILLER CAP DENGAN METODE TAGUCHI DAN ANALYSIS OF VARIENCE (ANOVA). S1 thesis, Universitas Mercu Buana Jakarta.

[img]
Preview
Text (HAL COVER)
1. Halaman Judul.pdf

Download (208kB) | Preview
[img]
Preview
Text (ABSTRAK)
2. Abstrak.pdf

Download (159kB) | Preview
[img]
Preview
Text (LEMBAR PERNYATAAN)
3. Lembar Pernyataan.pdf

Download (923kB) | Preview
[img]
Preview
Text (LEMBAR PENGESAHAN)
4. Halaman Pengesahan.pdf

Download (70kB) | Preview
[img]
Preview
Text (KATA PENGANTAR)
5. Kata Pengantar.pdf

Download (141kB) | Preview
[img]
Preview
Text (DAFTAR ISI)
6. Daftar Isi.pdf

Download (331kB) | Preview
[img]
Preview
Text (DAFTAR TABEL)
7. Daftar Tabel.pdf

Download (139kB) | Preview
[img]
Preview
Text (DAFTAR GAMBAR)
8. Daftar Gambar.pdf

Download (259kB) | Preview
[img]
Preview
Text (DAFTAR LAMPIRAN)
9. Daftar Lampiran.pdf

Download (89kB) | Preview
[img] Text (BAB I)
10. Bab 1.pdf
Restricted to Registered users only

Download (995kB)
[img] Text (BAB II)
11. Bab 2.pdf
Restricted to Registered users only

Download (4MB)
[img] Text (BAB III)
12. Bab 3.pdf
Restricted to Registered users only

Download (853kB)
[img] Text (BAB IV)
13. Bab 4.pdf
Restricted to Registered users only

Download (1MB)
[img] Text (BAB V)
14. Bab 5.pdf
Restricted to Registered users only

Download (331kB)
[img] Text (DAFTAR PUSTAKA)
15. Daftar Pustaka.pdf
Restricted to Registered users only

Download (529kB)
[img] Text (LAMPIRAN)
16. Lampiran.pdf
Restricted to Registered users only

Download (257kB)

Abstract

Almost every product used in everyday is made of plastic and most of these products can be produced by injection molding methods. A good mold will produce a product that matches the expected shape and dimensions. The existence of shrinkage causes discrepancies between the dimensions of the mold with the product. Inaccurate products can affect the function of a product. Oil filler cap is an automotive component that have function as a cover for oil filling holes in the automatic engine 110 cc, inaccurate oil filler cap can cause oil to seep out. To resolve this problem, it is necessary to make a precise oil filler cap. By simulating the process using the Autodesk Moldflow Insight software, optimal process parameters can be identified so that the minimum shrinkage is obtained. From the simulation results, it was found that the optimal parameter combination for the plastic molding process of oil filler cap products included injection temperature of 200 ° C, mold temperature of 80 ° C, holding pressure of 105 MPa, and holding pressure time of 9 seconds. With these parameter settings, the shrinkage value for thread diameter is 0,55% (0.11 mm) from diameter mold is 20 mm. Keywords: injection molding, shrinkage, taguchi method, Autodesk Moldflow Insight, oil filler cap Hampir setiap produk yang digunakan dalam kehidupan sehari-hari melibatkan penggunaan plastik dan sebagian besar diantaranya dapat diproduksi dengan metode injection molding. Cetakan yang baik akan menghasilkan produk yang sesuai dengan bentuk dan dimensi yang diharapkan. Adanya shrinkage menyebabkan ketidaksuaian antara dimensi cetakan dengan produk. Produk yang tidak presisi dapat mempengaruhi fungsi dari suatu produk. Oil filler cap merupakan salah satu komponen otomotif yang berfungsi sebagai penutup lubang pengisian oli pada mesin motor matic 110 cc, oil filler cap yang tidak presisi dapat menyebabkan oli bisa merembes keluar. Untuk mengatasi masalah tersebut, maka perlu dibuat oil filler cap yang presisi. Dengan simulasi proses menggunakan software Autodesk Moldflow Insight dapat diketahui parameter proses yang optimal sehingga didapatkan shrinkage yang minimum. Dari hasil simulasi didapatkan kombinasi parameter optimal untuk proses cetak plastik produk oil filler cap diantaranya temperatur injeksi 200 °C, temperatur cetakan 80 °C, holding pressure 105 MPa, dan holding pressure time 9 detik. Dengan setting parameter tersebut didapatkan nilai shrinkage pada bagian diameter ulir sebesar 0,55% (0,11 mm) dari diameter cetakan 20 mm. Kata kunci: cetak plastik sistem injeksi, shrinkage, metode taguchi, Autodesk Moldflow Insight, oil filler cap

Item Type: Thesis (S1)
Call Number CD: FT/MSN. 20 117
Call Number: ST/13/21/027
NIM/NIDN Creators: 41318110046
Uncontrolled Keywords: cetak plastik sistem injeksi, shrinkage, metode taguchi, Autodesk Moldflow Insight, oil filler cap
Subjects: 100 Philosophy and Psychology/Filsafat dan Psikologi > 150 Psychology/Psikologi > 154 Subconscious and Altered States and Process/Psikologi Bawah Sadar > 154.6 Sleep Phenomena/Fenomena Tidur > 154.63 Dreams/Mimpi > 154.634 Analysis/Analisis
600 Technology/Teknologi > 620 Engineering and Applied Operations/Ilmu Teknik dan operasi Terapan > 621 Applied Physics/Fisika terapan > 621.8 Machine Engineering, Machinery/Teknik Mesin
600 Technology/Teknologi > 660 Chemical Engineering and Related Technologies/Teknologi Kimia dan Ilmu yang Berkaitan > 668 Technology of Other Organic Products/Teknologi Produk Organik Lainnya > 668.4 Plastics/Teknologi Plastik
600 Technology/Teknologi > 680 Manufacture For Specific Uses/Industri Pembuatan produk untuk penggunaan tertentu > 681 Precision Instruments/Produksi Instrumen Presisi > 681.6 Printing, Writing, Duplicating Machine/Produksi Mesin Cetak, Mesin Tulis, Mesin Pengganda
Divisions: Fakultas Teknik > Teknik Mesin
Depositing User: Rifky
Date Deposited: 25 Feb 2022 00:33
Last Modified: 10 Dec 2022 03:15
URI: http://repository.mercubuana.ac.id/id/eprint/52241

Actions (login required)

View Item View Item