SANDRA, DODI (2025) STUDI EKSPERIMENTAL PENGUKURAN VIBRASI MENGGUNAKAN ACCELEROMETER DAN SMARTPHONE PADA GEDUNG BETON BERTULANG (Studi kasus : Gedung Perkantoran 36 Lantai di Jakarta Utara). S2 thesis, Universitas Mercu Buana Jakarta.
|
Text (HAL COVER)
COVER.pdf Download (413kB) | Preview |
|
![]() |
Text (BAB I)
BAB I.pdf Restricted to Registered users only Download (73kB) |
|
![]() |
Text (BAB II)
BAB II.pdf Restricted to Registered users only Download (642kB) |
|
![]() |
Text (BAB III)
BAB III.pdf Restricted to Registered users only Download (1MB) |
|
![]() |
Text (BAB IV)
BAB IV.pdf Restricted to Registered users only Download (1MB) |
|
![]() |
Text (BAB V)
BAB V.pdf Restricted to Registered users only Download (77kB) |
|
![]() |
Text (DAFTAR PUSTAKA)
DAFTAR PUSTAKA.pdf Restricted to Registered users only Download (63kB) |
|
![]() |
Text (LAMPIRAN)
LAMPIRAN.pdf Restricted to Registered users only Download (1MB) |
Abstract
Excessive vibrations in the floor system not only make building occupants uncomfortable, but the floor cannot be used to store equipment that is sensitive to vibration. The floor system using joist plates and beams is one of the structural systems on long-span beams, but with the length of the span it can cause vibrations in the floor structure to increase and potentially interfere with the activities of the building users. In this study, we will discuss alternative vibration measuring devices other than Accelerometers , namely by using Smartphones , where the measurement results of each device are in the form of wave speed and acceleration against time, then analyzed using the Fast Fourier Transformation (FFT) method to obtain the dominant frequency value . The test was carried out by giving an Impact load to the center of mass of the floor which was used as the test location point by installing 6 Accelerometer sensor points placed at ¼ span, ½ span, and ¾ span of the floor plate and at the same center of mass of the floor vibration measurements were also carried out using Smartphone with Vibration Pro application . The test was conducted on a 36-story reinforced concrete building, where the floors that can be tested are limited to floors 7, 17, 23 and 25. Each floor that was tested for vibration with Accelerometer and Smartphone was also subjected to numerical analysis with Etabs program modeling to obtain a comparison of the natural frequency values of the structure. The results of the analysis show that the frequency values of the three methods obtained almost the same natural frequency values, so the author concludes that communication devices such as smartphones can also be used to measure the frequency values of buildings or other structural components, for example on the 7th floor the natural frequency value was obtained using Accelerometer = 6.8393 Hz, Smartphone = 6.8607 and modeling with Etabs = 6.8350 Hz. After obtaining the natural frequency value of the structure, the Peak Acceleration value was also calculated numerically from the etabs program to then be checked against the comfort factor. The comfort reference standards used are SCI P354, ISO 2631 and AISC DG 11. The results of vibration test analysis on comfort factors for all floors tested are The natural frequency value of the plate still meets the minimum limit of the natural frequency of the plate required by SCI P354, which is ≥ 3 Hz, the natural frequency value still meets the permissible limit value for structures in the health category (0.5-80 Hz) according to ISO 2631 and the results of plotting the peak acceleration value and natural frequency of the structure on the AISC DG 11 curve are in the sensitive frequency zone felt by humans, so that the plate and joist beam do not meet the comfort requirements. Keywords : Vibration analysis, multi-storey buildings, vibration pro , Fast Fourier Transform (FFT), Comfort. Getaran berlebihan pada sistem lantai tidak hanya membuat penghuni gedung tidak nyaman, namun lantai tersebut tidak dapat digunakan untuk menyimpan peralatan yang sensitif terhadap getaran. Sistim lantai dengan menggunakan pelat dan balok joist merupakan salah satu sistem struktur pada balok dengan bentang panjang, namun dengan panjangnya bentang dapat menyebabkan vibrasi pada struktur lantai akan semakin besar dan berpotensi mengganggu aktivitas dari pengguna bangunan tersebut. Dalam penelitian ini akan dibahas mengenai alternatif alat pengukur vibrasi selain Accelerometer yaitu dengan menggunakan Smartphone, dimana hasil pengukuran masing-masing perangkat berupa kecepatan dan percepatan gelombang terhadap waktu, kemudian dianalisis menggunakan metode Fast Fourier Transformation (FFT) untuk mendapatkan nilai dominan frekuensi. Pengujian dilakukan dengan cara memberi beban Impact pada pusat masa lantai yang dijadikan titik lokasi pengujian dengan memasang 6 titik sensor Accelerometer yang ditempatkan pada ¼ bentang, ½ bentang, dan ¾ bentang pelat lantai dan pada pusat masa lantai yang sama juga dilakukan pengukuran vibrasi menggunakan Smartpone dengan aplikasi Vibration Pro. Pengujian dilakukan pada gedung beton bertulang 36 lantai, dimana lantai-lantai yang dapat diuji terbatas pada lantai 7,17,23 dan 25. Setiap lantai yang diuji vibrasi dengan alat Accelerometer dan Smartphone juga dilakukan analisa numerik dengan pemodelan program Etabs untuk mendapakan perbandingan nilai frekuensi alami struktur. Hasil analisis menunjukkan bahwa nilai frekuensi dari ketiga metoda tersebut didapatkan nilai frekuensi natural yang hampir sama, sehingga penulis menyimpulkan bahwa perangkat komunikasi seperti smartphone juga dapat digunakan untuk mengukur nilai frekuensi bangunan atau komponen struktur lainnya, misalnya pada lantai 7 didapat nilai frekuensi natural menggunakan Accelerometer = 6,8393 Hz, Smartphone = 6,8607 dan pemodelan dengan Etabs = 6,8350 Hz. Setelah mendapatkan nilai frekuensi alami struktur dihitung juga nilai Peak Acceleration dengan cara numerik dari program etabs untuk selanjutnya dicek terhadap faktor kenyamanan. Standar acuan kenyamanan yang digunakan adalah SCI P354, ISO 2631 dan AISC DG 11. Hasil analisis pengujian vibrasi terhadap faktor kenyamanan untuk semua lantai yang diuji adalah Nilai frekuensi natural pelat masih memenuhi batas minimum frekuensi natural pelat yang disyaratkan SCI P354 yaitu ≥ 3 Hz, nilai frekuensi natural masih memenuhi nilai batas yang diijinkan untuk struktur pada kategori kesehatan (0,5-80 hz) menurut ISO 2631 dan hasil plotting nilai peak acceleration dan frekuensi alami struktur pada kurva AISC DG 11 berada dalam zona frekuensi sensitif yang dirasakan manusia, sehingga pelat dan balok joist tidak memenuhi syarat kenyamanan. Kata kunci: Analisis getaran, bangunan bertingkat, vibration pro, Fast Fourier Transform (FFT), Kenyamanan.
Actions (login required)
![]() |
View Item |