PERANCANGAN RANGKA PANEL SURYA UNTUK ATAP WARUNG KOPI DI KEBON JERUK DENGAN MENGGUNAKAN SIMULASI SOLIDWORKS

DARUSSALAM, DENIS (2021) PERANCANGAN RANGKA PANEL SURYA UNTUK ATAP WARUNG KOPI DI KEBON JERUK DENGAN MENGGUNAKAN SIMULASI SOLIDWORKS. S1 thesis, Universitas Mercu Buana Jakarta.

[img]
Preview
Text (HAL COVER)
01 Cover.pdf

Download (589kB) | Preview
[img] Text (BAB I)
02 BAB I.pdf
Restricted to Registered users only

Download (33kB)
[img] Text (BAB II)
03 BAB II.pdf
Restricted to Registered users only

Download (425kB)
[img] Text (BAB III)
04 BAB III.pdf
Restricted to Registered users only

Download (1MB)
[img] Text (BAB IV)
05 BAB IV.pdf
Restricted to Registered users only

Download (885kB)
[img] Text (BAB V)
06 BAB V.pdf
Restricted to Registered users only

Download (25kB)
[img] Text (DAFTAR PUSTAKA)
08 Daftar Pustaka.pdf
Restricted to Registered users only

Download (75kB)
[img] Text (LAMPIRAN)
09 Lampiran.pdf
Restricted to Registered users only

Download (421kB)

Abstract

Solar energy is a renewable energy that is very abundant which can be converted into electricity through photovoltaic (PV). In Indonesia, with the enormous potential for sunlight, it is hoped that solar cells can be used as a source of electricity in Indonesia. The purpose of this research is to replace the previous installation of solar panels that still cover the tile roof / double installation, so the authors make a solar panel frame design to determine the use of solar panels as the roof of the building directly. Here the author will try to replace the roof of the building using solar panels (photovoltaic) with an building integrated photovoltaic (BIPV) system. Therefore, the solar panel frame is analyzed using solidworks simulations to find out how much critical stress and shape changes occur when the load is applied. Geometry results that can be used as a canopy as a coffee shop terrace roof and also as a solar panel frame with dimensions of 3.1 m high, 3.5 m long, 2.1 m wide, and a tilt angle of 8.5o with a solar panel pedestal distance of 0 .55 m and the design results that have been simulated can be seen that the structure and material of the canopy frame given a dead load of 53.5 kg, dead load and live load (worker tire) of 123.5 kg, dead load and wind load of 59 kg , dead load and rain load of 67 kg, and a total load of 72,5 kg resulted in stress of 155, 357, 170, 193, 209 kgf/cm2. The displacements are 0,6 mm, 1.4, 0.6, 0.7, 0.8 mm, respectively. And for the safety of factors, each is 13, 12, 6, 11, 10 FOS. Keywords: renewable energy, hollow galvanized, BIPV, finite element analysis, static analysis. Energi surya merupakan energi terbarukan yang tersedia sangat melimpah yang dapat di konversikan menjadi listrik melalui photovoltaic (PV). Di Indonesia, dengan potensi sinar matahari yang sangat besar, diharapkan sel surya dapat digunakan sebagai sumber listrik di Indonesia. Tujuan dari penelitan ini adalah mengganti pemasangan sebelumnya panel surya masih melapisi atap genting/double instalasi untuk itu penelitian ini membuat perancangan rangka panel surya untuk mengetahui penggunaan panel surya sebagai atap bangunan langsung. Di penelitian ini akan mencoba untuk mengganti atap bangunan menggunakan panel surya (photovoltaic) dengan sistem building integrated photovoltaic (BIPV). Oleh karena itu, rangka panel surya dianalisa dengan simulasi solidworks untuk mengetahui berapa besar tegangan kritis dan perubahan bentuk yang terjadi pada saat beban diaplikasi. Hasil geometri yang dapat dijadikan kanopi sebagai atap teras warung kopi dan juga sebagai rangka panel surya dengan dimensi tinggi 3,1 m, panjang 3,5 m, lebar 2,1 m, dan sudut kemiringan 8,5o dengan jarak tumpuan panel surya sebesar 0,55 m dan hasil desain yang telah disimulasikan dapat diketahui bahwa struktur dan material dari rangka kanopi yang diberikan beban mati 53,5kg, beban mati dan beban hidup (beban pekerja) sebesar 123,5kg, beban mati dan beban angin sebesar 59 kg, beban mati dan beban hujan sebesar 67 kg, dan beban keseluruhan sebesar 72,5 kg mengakibatkan tegangan (stress) masing-masing sebesar 155, 357, 170, 193, 209 kgf/cm2. Untuk displacement (perpindahan) masing-masing sebesar 0.6, 1.4, 0.6, 0.7, 0.8 mm. Dan untuk safety of factor masing-masing sebesar 13, 6, 12, 11, 10 FOS. Kata Kunci: energi terbarukan, hollow galvanis, BIPV, finite element analysis, static analysis.

Item Type: Thesis (S1)
NIM/NIDN Creators: 41317010009
Uncontrolled Keywords: energi terbarukan, hollow galvanis, BIPV, finite element analysis, static analysis.
Subjects: 600 Technology/Teknologi > 620 Engineering and Applied Operations/Ilmu Teknik dan operasi Terapan
600 Technology/Teknologi > 620 Engineering and Applied Operations/Ilmu Teknik dan operasi Terapan > 621 Applied Physics/Fisika terapan
600 Technology/Teknologi > 620 Engineering and Applied Operations/Ilmu Teknik dan operasi Terapan > 621 Applied Physics/Fisika terapan > 621.8 Machine Engineering, Machinery/Teknik Mesin
600 Technology/Teknologi > 650 Management, Public Relations, Business and Auxiliary Service/Manajemen, Hubungan Masyarakat, Bisnis dan Ilmu yang Berkaitan > 653 Shorthand/Penulisan Cepat, Penulisan dengan Tangan > 653.3 Machine Systems/Sistem Mesin
Divisions: Fakultas Teknik > Teknik Mesin
Depositing User: Dede Muksin Lubis
Date Deposited: 03 Jan 2022 04:09
Last Modified: 03 Jan 2022 04:09
URI: http://repository.mercubuana.ac.id/id/eprint/53411

Actions (login required)

View Item View Item